Laundry room with a front-loading washer and tumble dryer

Tumble dryers

Tumble Dryer Repairs

Vented, condenser and heat-pump tumble dryers. If yours runs but won’t heat, won’t turn, or leaves the washing damp after a full cycle, we’ll find out why.

About this service

How we approach tumble dryer repairs

A tumble dryer depends on three things working together: heat, airflow and tumbling. Heating elements, thermal fuses and thermostats produce and control the heat; the fan, lint filter and vent or condenser move the moist air out; and the motor, belt and drum rollers keep the load turning.

Restricted airflow is behind a large share of dryer complaints. A blocked filter, vent hose or condenser makes drying slow and can make the dryer overheat and trip its safety cut-out — so we always check the airflow before replacing heating parts.

Safety matters with dryers. If you notice a burning smell, unplug the dryer and stop using it until it has been checked.

What we work on

  • Vented dryers
  • Condenser dryers
  • Heat-pump dryers
  • Washer-dryer drying faults

Common problems

Tumble dryer faults we see most often

The symptom points us in the right direction — testing confirms the cause.

  • 01

    Runs but no heat

    A failed heating element, blown thermal fuse or faulty thermostat. On vented models, a blocked vent can trip the cut-out.

  • 02

    Drum not turning

    If the motor hums but the drum stays still, the drive belt has usually snapped or slipped off.

  • 03

    Takes far too long to dry

    A blocked lint filter or vent hose, a full water container or dirty condenser, or a faulty moisture sensor.

  • 04

    Squeaking or thumping

    Worn drum rollers or bearings, a tired idler pulley or a damaged drum felt seal.

  • 05

    Won’t start

    Door switch, start switch, thermal fuse or control-board faults.

  • 06

    Overheating or burning smell

    Usually an airflow restriction. Stop using the dryer until it has been inspected.

Safety tip

Clean the lint filter after every load. A blocked filter makes drying slow and is a fire risk. On condenser dryers, empty the water container and rinse the condenser as your manual recommends.

Front-loading tumble dryer with its door open

The repair process

What happens when we repair your tumble dryer

  1. Check airflow first

    Filter, vent hose or condenser unit are inspected for blockages.

  2. Test the heat circuit

    Element, thermal fuse and thermostats are tested for continuity.

  3. Inspect the drive

    Belt, rollers, idler pulley and motor are checked for wear.

  4. Explain and quote

    You approve the price before any parts are fitted.

  5. Repair and heat test

    We run the dryer to confirm it heats, turns and switches off correctly.

Why choose CLEARFIX

Why customers book CLEARFIX for tumble dryer repairs

  • Airflow checked every time

    We look for the cause of overheating, not just the part that failed because of it.

  • Safety-focused repairs

    Thermal fuses and cut-outs exist for a reason — we never bypass them.

  • At your home

    Dryers are diagnosed and repaired where they’re installed.

FAQ

Tumble dryer repairs: your questions answered

Still unsure? Send us the details or a WhatsApp with a photo of the problem.

The heat is there but the moist air isn’t leaving — usually a blocked filter, vent hose or condenser, or a faulty moisture sensor ending the cycle early.

It isn’t recommended. The hose carries hot, moist, lint-filled air out of the room. Without it you’ll get condensation and lint build-up indoors. Follow the installation instructions in your manual.

Check your manual — most condenser dryers have a removable condenser unit that needs rinsing regularly. A clogged condenser is a common cause of slow drying.

It can be the thermal cut-out protecting the dryer from overheating, which usually points to an airflow problem. Book a check rather than keep restarting it.